Closing, Venting and Dispensing

The patented FLUXX^®-Dispensing Taps for containers and drums are perfectly suitable for simple, clean and quick refilling of fluids without gurgling. The outstanding flow properties are based on the patented ventilation system.

FLUXX®-Dispensing Taps are suitable for plastic containers and bottles with thread sizes:

• DIN 38
• DIN 40
• DIN 45
• DIN 50
• DIN 51
• DIN 61
• DIN 71

Plastic or metal drums with internal threads of:​

• ¾“ BSP
• 2“-fine-pitch thread (TriSure^®)
• 2“-coarse-pitch thread (Mauser)

All raw materials and additives used for production are non-hazardous. They are physiologically acceptable and in line with the EC directive 2002/72 as well as the German Food and Feed Code (LFGB).

SABEU develops and produces membranes used in our vents and vented closures. They offer crucial advantages for the packaging of gas emitting materials.

FLUXX^® packaging vents are equipped with PTFE membranes, which allow for continuous pressure equalization, while preventing pressure build-up and suppression of containers. The patented FLUXX^® drip-off edge allows fluids to drain immediately after coming into contact with the membrane, keeping the membrane unobstructed and permeable to air.

Properties:

• allow the continuous pressure release
• prevent the swelling, bursting or collapsing of containers
• allow the quick re-ventilation after contact with fluids
• provide a reliable protection against leaks
• are easy to install
• are suitable for a high number of applications

Intended for the packaging of:

• Industrial chemicals
• Bleaching agents
• Peroxides
• Fertilizers
• Pool chemicals
• Pesticides
• Sterilizers
• Disinfectants and cleaning agents
• Foods (comply with EC and FDA regulations)

Based on their configuration and structural design, the FLUXX^® packaging vents meet all the requirements for the approval with suitable containers set forth in the UN test specifications, ADR, and the BAM [German Federal Institute for Materials Research and Testing] dangerous goods regulation, BAM-GGR 005.

FLUXX^® Screw Caps for standardized industrial containers are available for the following thread sizes:

• DIN 45 with molded tamper-evidence ring
• DIN 51 with or without tamper-evidence ring / molded on or attached
• DIN 61 with or without tamper-evidence ring / molded on or attached

All screw caps are:

• also available with degassing system
• suitable for packaging of dangerous goods
• available with different sealing rings or disks (EPE, rubber, PVC, PTFE)

FLUXX^®-Vented Caps for standardized industrial containers are available in the following thread sizes:

• DIN 45 with molded on tamper-evidence ring
• DIN 51 with or without tamper-evidence ring / molded on or attached
• DIN 61 with or without tamper-evidence ring / molded on or attached

FLUXX^®-Vented Caps are:

• equipped with the SAVE-Degassing System
• available with a variety of sealing rings (EPE, rubber, PVC, TPE)
• suitable for packaging dangerous goods

Intended for the packaging of:

• Industrial chemicals
• Bleaching agents
• Peroxides
• Fertilizers
• Pool chemicals
• Pesticides
• Sterilizers
• Disinfectants and cleaning agents
• Foods in the EC

Based on their configuration and structural design, our vented caps meet all the requirements for the approval for use with suitable containers and bottles as set forth in the ADR test specifications and the BAM dangerous goods regulation, BAM-GGR 005.

FLUXX^®-Sealing Caps for induction heat sealing are available for bottles and containers with thread sizes:

• DIN 45
• DIN 50
• DIN 60
• DIN 63

Based on their configuration and structural design, our seals meet all the requirements for approval with suitable canisters and bottles as set forth in ADR, UN test specifications and the BAM dangerous goods regulation, BAM-GGR 005.

FLUXX^® barrel seals are designed for metal or synthetic barrels with a capacity of up to 200 liters with the following thread dimensions:

• ¾“ BSP
• 2“ fine thread (TriSure^®)
• 2“ coarse thread (Mauser^®)
• DIN 63

They are optionally available with an LD-PE or EPDM sealing ring and if necessary also with an integrated degassing insert.

Based on their configuration and structural design, our drum closures meet all the requirements for approval with suitable containers as set forth in ADR, UN test specifications and the BAM dangerous goods regulation, BAM-GGR 005.

FLUXX^® nozzles and tube tips are made of PE-HD and are highly resistant to acids, bases, water, alcohols, oil and gasoline. Thanks to the non-polar and hydrophobic surface, our tube tips are particularly suitable for use with plastic adhesive, joint fillers and sealing compounds.

FLUXX^® tube tips are supplied with metric thread sizes of:

• M15 x 1,5
• M20 x 1,5

and are compatible with the most common cartridges and tubes.

All raw materials and additives used for the production process are non-hazardous to the health, physiologically unobjectionable and in line with the EC directive 2002/72 as well as the German Food and Feed Code (LFGB).

Die FLUXX^®-Shaker Cans are made of polypropylene (PP). The covering caps are available in different colors. The sprinkling inserts are available in two different variations. They are sealed with a trilingual hygiene seal “Hier abziehen/enlever ici/take off here“, guaranteeing the integrity of the contents to the customer.

All raw materials and additives used for the production process are non-hazardous to the health, physiologically unobjectionable and in line with the EC directive 2002/72 as well as the German Food and Feed Code (LFGB).